Product Description
The Braemar Wall Furnace Heaters Manual Over Heat Switch 130°C (Part Number: BGH266) is a safety feature designed to protect your Braemar wall furnace heater from potential overheating. If the heater's temperature exceeds the critical threshold of 130°C, the overheat switch will trigger, cutting off power or gas to the unit to prevent damage or fire hazards. After the switch is activated, it requires manual resetting before the heater can be used again.
Key Features of the Braemar Wall Furnace Heaters Manual Over Heat Switch 130°C (BGH266):
-
Overheat Protection at 130°C:
- The 130°C threshold is the critical temperature point at which the manual overheat switch activates. If the heater operates at or above this temperature, the switch will disconnect the heater from its power or fuel source to prevent further heating.
-
Manual Reset:
- Unlike automatic overheat switches, this particular manual overheat switch requires users to reset it manually. After activation, it is important to inspect the unit for any issues causing the overheating before resetting the switch to ensure the heater’s safety.
-
Enhanced Safety:
- The overheat switch helps to protect the heater’s internal components, such as the heat exchanger and gas control system, by cutting off the operation when excessive heat is detected. This can prevent long-term damage to the heater and reduce the risk of fire hazards or system failure.
-
Compatibility:
- This overheat switch (Part No. BGH266) is designed specifically for Braemar wall furnace heaters. It should be compatible with a range of Braemar models, especially those that have a 130°C safety cut-off point. Always verify compatibility with your specific model.
-
Durability and Reliability:
- Built to be durable and reliable, this overheat switch is designed to handle the high-temperature environments inside the heater, ensuring long-lasting protection.
Installation of the Braemar Wall Furnace Heaters Manual Over Heat Switch 130°C (BGH266):
-
Turn Off the Gas and Electricity:
- Before replacing the overheat switch, disconnect the gas supply and turn off the power to the heater. This ensures safety during installation and prevents accidents.
-
Access the Heater:
- You may need to remove the front panel or access cover of the heater to reach the overheat switch. This will vary depending on the specific model of your Braemar wall furnace heater.
-
Remove the Old Overheat Switch:
- Disconnect the wiring from the old overheat switch. You may need a screwdriver to unscrew the switch from its mounting position. Carefully remove the faulty switch.
-
Install the New Overheat Switch (BGH266):
- Place the new manual overheat switch (BGH266) into the same position where the old switch was mounted. Secure it using screws or clips provided with the new switch.
- Reconnect the wiring to the terminals of the new switch, making sure that the connections are firm and secure.
-
Reassemble the Heater:
- After installing the new switch, carefully reassemble any panels or covers that were removed to access the switch.
-
Turn the Gas and Power Back On:
- Once everything is securely installed, turn the gas supply and electricity back on to the heater.
-
Test the Heater:
- Run the heater for a brief period and ensure that it operates normally. If the heater exceeds 130°C, the overheat switch should activate, cutting off the heat and ensuring that the unit does not operate under unsafe conditions.
Troubleshooting:
-
Overheat Switch Frequently Triggers:
- If the overheat switch keeps triggering, it could be due to insufficient airflow around the heater or a blocked heat exchanger. Check that the vents and airways are clear, and ensure that the room has adequate ventilation.
-
Manual Reset Not Working:
- If the switch does not reset, ensure the heater is completely cool before attempting to reset the switch. If the switch still does not reset, it could indicate a malfunction in the switch or another issue with the heater. In this case, contact a technician for further assistance.
-
Difficulty Installing the Switch:
- If you're having trouble with the installation, ensure you're following the correct procedure. Refer to the Braemar heater manual or consult a professional technician to help install the new overheat switch.
Conclusion:
The Braemar Wall Furnace Heaters Manual Over Heat Switch 130°C (BGH266) is an essential safety component designed to protect your Braemar heater from overheating. It ensures that the heater will shut off if the temperature exceeds 130°C, preventing potential damage or safety hazards. By requiring manual reset, the switch encourages proper inspection before the heater is used again.