Product Description
The Braemar Wall Furnace Heaters Manual Over Heat Switch 100°C is a safety component designed to help protect Braemar wall furnace heaters from overheating. If the heater exceeds a critical temperature, the manual overheat switch can be triggered, ensuring that the system shuts down to prevent potential damage or hazards.
Key Features of the Braemar Wall Furnace Heaters Manual Over Heat Switch 100°C:
-
Overheat Protection:
- The manual overheat switch is set to activate when the heater’s temperature exceeds 100°C. This is a crucial safety feature that ensures the heater does not operate under unsafe conditions, preventing potential damage to internal components or even fire hazards.
-
Manual Reset:
- Unlike automatic overheat switches, the manual overheat switch requires the user to manually reset the switch after it has been triggered. This helps ensure that the heater is properly checked and serviced before being used again.
-
Safety Mechanism:
- This switch acts as an additional safety mechanism that helps to protect the heater. If overheating occurs due to factors like a malfunction, blocked ventilation, or poor airflow, the switch will stop the heater from functioning until it is reset and the issue is resolved.
-
Temperature Setting:
- The 100°C threshold is designed to be a critical point that ensures the internal components of the heater are not subjected to extreme temperatures. This is generally a high-temperature point, which helps prevent the system from operating in unsafe conditions.
-
Easy to Install and Replace:
- The Braemar manual overheat switch is easy to install and replace. It is usually a direct replacement for the old or faulty overheat switch, making it a simple task for most users or technicians to perform.
-
Compatibility:
- This manual overheat switch is compatible with Braemar wall furnace heaters and fits a variety of models. Always check the specific model of your heater to ensure compatibility with the overheat switch.
Installation of the Braemar Wall Furnace Heaters Manual Over Heat Switch 100°C:
-
Turn Off Gas and Electricity:
- Before performing any maintenance or installation, ensure that both the gas supply and electricity to the heater are turned off to avoid any accidents.
-
Access the Heater:
- The manual overheat switch is typically located within the heater’s control panel or near the heat exchanger. You may need to remove the cover or access panels of the heater to gain access to the switch.
-
Remove the Faulty Overheat Switch:
- Disconnect the wiring from the old overheat switch and remove any screws or fasteners that may be holding it in place. Carefully remove the faulty switch.
-
Install the New Overheat Switch:
- Install the new Braemar manual overheat switch in the same location as the old one. Ensure that the switch is securely mounted and that the wiring is connected correctly. Tighten any screws or fasteners to hold the switch in place.
-
Check the Wiring and Connections:
- Double-check the wiring connections to ensure that everything is securely attached and there are no loose or exposed wires. Correctly wired connections are essential for the proper operation of the overheat switch.
-
Reassemble the Heater:
- Once the switch is installed and connected, replace the cover or panels of the heater that were removed during installation.
-
Test the Heater:
- After reassembling the heater, turn the gas supply and electricity back on. Test the system by running the heater for a short time to ensure it is operating properly. If the temperature exceeds 100°C, the switch should trigger and stop the heater, ensuring it functions correctly.
Troubleshooting:
-
Overheat Switch Triggering Frequently:
- If the manual overheat switch keeps triggering, it could be a sign that the heater is overheating due to insufficient ventilation or a blocked heat exchanger. Check that the heater's vents and airways are clear, and ensure the room is properly ventilated.
-
Heater Not Resetting After Overheat:
- If the manual overheat switch does not reset after the heater cools down, ensure the switch is properly connected. If necessary, consult the user manual or a professional technician to confirm if any further issues need to be addressed.
-
Difficulty Removing or Installing the Switch:
- If you are having trouble removing or installing the switch, it could be helpful to refer to the Braemar wall furnace manual for specific instructions for your model. Alternatively, contacting a licensed technician might be necessary to prevent any damage.
Conclusion:
The Braemar Wall Furnace Heaters Manual Over Heat Switch 100°C provides important overheat protection for Braemar gas heaters. By ensuring that the heater shuts off when it reaches an unsafe temperature, this switch helps to prevent overheating and potential damage. It is easy to install and reset, making it an essential safety component for maintaining a safe and efficient heating system.